QUESTIONS?As a manufacturer, we are com-mitted to providing completecustomer satisfaction. If you havequestions, or find there are miss-ing or damaged
14. Cut the plastic zip tie (not shown) from the Cable(35). Be careful not to damage the Cable.Pull on the Cable (35) until you have enough slackto ro
18. Insert a 1/4Ó x 2 1/2Ó Carriage Bolt (57) through thecenter hole in a Seat Plate (29). Attach the SeatPlate to the Seat (23) with two 1/4Ó x 3/4Ó
12ADJUSTMENTThe instructions below describe how each part of the home gym system can be adjusted. Refer to the exerciseguide accompanying this manual
13ATTACHING THE LAT BAR, ROW BAR, OR NYLONSTRAP TO THE LOW PULLEY STATIONAttach the Lat Bar (21) to the Cable (35) with a CableClip (38). For some exe
14TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. Thehome gy
15CABLE DIAGRAMThe cable diagram below shows the proper routing of the Cable (35). Use this diagram to be sure that the Cablehas been assembled correc
3/8" Nylon Locknut (39)3/8" Washer (46)1/2" x 3 1/2" Carriage Bolt (49)1/2" Nylon Jam Nut (50)3/8" x 2 1/2" Bolt (5
3/8" x 1" Bolt (16)3/8" x 2" Bolt (43)3/4" Tap Screw (62)1" Square Inner Cap (64)1 3/4" Square Inner Cap (65)2"
Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. PART LISTÑModel No. HRSY54370 R1197AKey No. Qty. Desc
313030303021232829292713262526272712262526273837415630242415142041417228218910401917424211339411424232344141414141414040304057575656555455545174533966
2TABLE OF CONTENTSLIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ORDERING REPLACEMENT PARTSTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday, 6
31. It is the responsibility of the owner to ensurethat all users of the home gym system areadequately informed of all precautions.2. Read all instruc
4BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height: 90 in. (Extended)Width: 48 in. Length: 59 in. The HealthRider¨BRSrequires a minimum ceilingheight of 7
5ASSEMBLY16060Before beginning assembly, carefully read thefollowing information and instructions:¥ Place all parts of the home gym system in acleared
2. Press four 2Ó Square Inner Caps (68) into theFrame (2).Identify the Left Wheel Channel (3) and the RightWheel Channel (4) by comparing the weldedbr
4. Slide the Support Tube (32) onto the Base (1).Attach the Support Tube to the Base with two 3/8Óx 2Ó Bolts (43) and two 3/8Ó Nylon Locknuts (39).Do
7. Lubricate the 1/2Ó x 3 1/2Ó Carriage Bolt (49).Attach the Lift Tube (11) to the Frame (2) with theCarriage Bolt and a 1/2Ó Nylon Jam Nut (50). 8. A
11. Press a 1Ó Round Inner Cap (36) into one of thePress Arms (6). Press a 1 3/4Ó Square Inner Cap(65) into the Press Arm.Repeat this step for the oth
Comments to this Manuals